How to make a self watering planter with a 5 gallon bucket

image

Container gardening can be an excellent way to take advantage of normally unusable space on your patio or garden.  The main problem I have with container gardens is they can dry out very quickly and for plants like tomatoes and cucumbers this can be a quick death for your plants, my solution to this was to build a self watering planter using just a few tools and a 5-gallon bucket and lid.

Materials for 5-gallon bucket self watering planter:

WP_20130601_005

  • 5 gallon bucket with lid
  • Another 5 gallon bucket busted one like mine is fine (optional)
  • 1.5 feet of 3/4 in PVC pipe (other sizes are ok but aim will have to be better for smaller sizes when watering)
  • Utility knife
  • 4 inch net pot
  • cheese cloth
  • Jig-saw (optional but speeds things up)

 

Construction for 5-gallon bucket self watering planter:

Step 1: Make hole for net pot.  I started by tracing the pot on the bottom of my broken bucket.

image

Obviously if I cut on this line I drew the net would fall right in so a freehanded a line inside with about 1/4 inch in and cut it out with a utility knife.  I chose a square net pot since straight lines are much easier with a knife but if I would going to make a half dozen of these things I probably would get a good hole saw and use some round net pots.

image

Step 2: Cut bucket to size.  For the desired height of the net pot in the reservoir I found that cutting the bottom of the bucket to 2.5 inches was perfect for me.  Now you can definitely to this with a utility knife, but a jig saw can make the job much quicker.

 

image

Step 3: Put some pieces together.  Now place the recently cut bucket bottom side up into the other bucket and push down until it is firmly in place.  Then drop in the net pot.

image

Step 4: Add watering tube.  I decided to cut the bottom of the tube at an angle to ensure that water flow was not blocked when pushed to the bottom (especially if some sediments starts to build up on the bottom.  I also used a hole saw to make sure I had a nice clean circle though this could be done with a utility knife as well with a little patience.

WP_20130601_019

Drop the filling tube in the hole and you are almost ready to start filling the planter with soil.

Step 5: Finishing touches.  I decided to add extra holes to enable some additional aeration from below.

image

To reduce soil from sneaking into the reservoir I lined the bottom with a couple layers of cheese cloth as a bit of a filter.

image

Finally I added a overfill hole approximately 1/4 of an inch below the top of the net pot.  This will prevent the plant from getting too much water and also allows a gap of air to exist between the water and the plant for additional aeration.

image

Step 6: Getting planter ready for plants.  Now it is time to to fill the planter with potting mix.  If you are using organic fertilizer like myself I added some to the mix and combined well in the bucket.  If you are using conventional fertilizer you will want to add a ring on the top of the soil around the perimeter of the planter.  This will ensure you do not shock/burn the newly added plants when they are added.

Next you should top the planter with some plastic.  This will keep weeds from getting in your soil but also help prevent water loss from evaporation.  You can use a dark color to provide some additional heat for something like peppers, but given I was planning on planting some cucumbers I went with white plastic which I conveniently reused from the bag the potting mix came in.  And secure it in place with the bucket lid where I removed the middle quickly with a utility knife.  Note: Don’t throw away the middle if you don’t have an extra bucket to sacrifice for a planter, with some minimal support (PVC pipe and zip ties this could be used as the bottom of a planter.

image

Step 7: Time to plant.  Start by cutting an X in the plastic to allow enough room to add you plant to you planter.

image

Finally drop in your plant and add water till you see water coming out of the overflow and enjoy your harvest to come with out having to worry about watering your container plants a couple times a day.

image

Just for fun when watering I did get some water on the plastic and poked a small hole where the water was piling up.  This will prevent having some standing water when it rains but also provide some free water to the reservoir.

So if you have little/no ground to plant or more like me and just get absent minded to water frequently for about $5-6 in parts and about 15-20 minutes of work you can make your own self-watering planter.

2 Responses to “How to make a self watering planter with a 5 gallon bucket”

  1. Tomatoes: Upside down, Ground, and Self Watering Container Says:

    […] Well I decided to do a little experiment and start several tomato plants from seeds and grow two in an official Topsy Turvy planter, two in the ground with fertile soil, and one in a homemade self watering container.  […]


  2. Tomato Container 5 Gallon 5 Gallon Bucket Gardening Self Watering Says:

    […] How to make a self watering planter with a 5 gallon bucket – Container gardening can be an excellent way to take advantage of normally unusable space on your patio or garden. The main problem I have with container gardens is they can dry out very quickly and for plants like tomatoes and cucumbers this … Construction for 5-gallon bucket self watering … […]


Leave a Reply

XHTML: You can use these tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

IKE